Jetex.org - FIZZLE QUICK 50 - JETEX PLANS


  You are here: Home / JETEX 50 / FIZZLE QUICK 50

Advanced Plan Search
User Panel
Username:

Password:

Log me on automatically next visit?

» Forgot password

 New Users

» Click here to Register!
 
Random Plan

MIG-15
MIG-15


 Plans with Great Build Guides

 »  HAWKER P-1081

 »  CUTLASS F7U-3

 



FIZZLE QUICK 50
FIZZLE QUICK 50

            

FIZZLE QUICK 50
Wing span: 24 Inches
Designed By: Ian Dowsett
Description: Fizzle Quick. Simple Jetex model for 50 or 100 power. Note two sizes of model are shown on the one plan, at wingspans of 15-3/4 and 23-3/4 inches.

In Dowsett's high performance contest design for Jetex. Fizzle Quick. Two for the price of one in this plan for the simplest of jetex '50' or '100' models with unique open frame fuselage structure.

AT THE 1954 All-Britain Rally we were endeavouring to report the annual Challenge Trophy for Jetex models and had the camera set at a high shutter speed to catch Ian Dowsett launching his unusual entry. Of went the jet - and our shutter, but we regret to say that we did not stop the model. Now this may sound a tall story when we can arrest the flight of other fast models as they are launched, but the fact remains that 'Fizzle-Quick' has a lightning acceleration which has to be seen to be believed.

The answer lies in its extreme light weight, minimum construction for maximum power, and the complete reduction of fuselage wetted area to a bare minimum, comprising a simple vertical 'A' frame. The 100 version finished in third place at the ICI Trophy and its best flight to date has been 5 minutes 42 seconds, whilst an average through the season rests at 2 minutes 15 seconds. Its smaller brother, the '50' has made 3 minutes, 37 seconds OOS with a steady average of 1 minute 45 seconds.

Construction is the same for both types and, if built exactly to plan, either version should present you with contest performance from the very first flight onwards.

Begin by laying the main longerons on the plan and joining them with the pylon construction. In the case of the 100 version there are two 1/16 x 3/16 strengtheners and, at the rear end, the sheet fin serves to make the longeron join more solid. Refer to the head-on view of the fuselage you are building so that you can see exactly how the pylon sheet is expected to fit on to the longerons.

When lifted from the plan, the wing and tail platforms are cemented in place, noting in the head-on cross-section views that the tailplane platform is inclined so that the right-hand tail tip is much higher than the left. This provides the turn trim for the glide. Add the small wire hooks for the elastic bands and the unit clips.

The wing and tail are as simple as one could desire with a flat-bottomed wing section and curved spar in the tips of the 100 version to help prevent warps. Both tailplane sections are flat.

Flying. Designed to save weight, neither version will require nose weight if built according to plan. The unit is set at straight thrust and slight right rudder may be required to assist the tilted tailplane in obtaining the-right hand spiral climb and right-hand glide. A tip-up tailplane dethermaliser is advised and the rear portion of the wing acts as a limit stop. The tailplane is simply retained in each place with an elastic band from the tail hook forwards and over the under-fin, and a fuse-loaded band passing back-wards to the hook at the bottom of the fuselage.

Be sparing with the dope and use lightweight tissue with a bright colour scheme for visibility and you will soon be enjoying some impressive flights at very little expense. Did we hear someone say what happens if the longerons break? Well, they have not broken as yet and if they so happen to go - then replacement will only be a matter of a copper or two!
Keywords: fizzle quick jetex 50 Ian Dowsett
Hits: 753
Downloads: 1
Rating: 0.00 (0 Vote(s))
 



Previous plans:
   FIZZLE BUG  
 Next plan:
FIZZLE XIII